GF laser cutting machine

Price range: USD 7,000 – 50,000 (depending on configuration · FOB Qingdao)

High-power fiber laser, 6–60 kW, on a compact 3000 × 1200 mm bed: Raytools/WSX auto-focus head, Yaskawa/Fuji servos, Hiwin rails, ±0.03 mm, 100 m/min.

  • CE / ISO 9001
  • 24-month warranty
  • FOB Qingdao
  • Remote & on-site support

GF3012: Overview

The GF3012 puts a high-power fiber source, from 6 kW up to 60 kW, on a compact 3000 × 1200 mm bed. It is for shops that cut thick plate into small and medium parts and want the power without the floor space of a 4020 or 6020 machine. The motion is built around an auto-focus head, Yaskawa or Fuji servo drives and Hiwin rails.

3000 × 1200 mmworking area
6–60 kWfiber laser power
±0.03 mmX/Y positioning
100 m/minmax linkage speed
Fiber laser cutting head over steel plate
Auto-focus cutting head.

Technical Specifications

GF3012 – standard data
Working area3000 × 1200 mm
Laser power6–60 kW fiber
X/Y positioning accuracy±0.03 mm
Max linkage speed100 m/min
Cutting headRaytools or WSX auto-focus
DriveYaskawa or Fuji servo motors, Hiwin linear rails
File formatsAI, BMP, PLT, DXF, DST and others
MaterialsCarbon steel, stainless steel, aluminium, brass
CertificationCE, ISO 9001
Warranty24 months on the whole machine (consumables excluded)

What the Power Options Cut

Typical maximum thickness from 1 kW to 60 kW; the last column marks the powers this machine can carry. Treat the figures as the ceiling, not the daily working range. At these powers the GF3012 is a thick-plate machine. On thin sheet the extra kilowatts add little, because acceleration sets the pace there.

Typical maximum cutting thickness by laser power, 1 kW to 60 kW
Laser powerCarbon steel (O₂)Stainless (N₂)Aluminium (N₂)Brass (N₂)This model
1 kW10 mm5 mm3 mm3 mm–
1.5 kW16 mm6 mm4 mm3 mm–
2 kW20 mm8 mm6 mm5 mm–
3 kW22 mm10 mm8 mm6 mm–
4 kW25 mm12 mm10 mm8 mm–
6 kW25 mm20 mm16 mm12 mm✓
8 kW40 mm30 mm30 mm16 mm✓
12 kW40 mm40 mm40 mm16 mm✓
20 kW80 mm100 mm60 mm20 mm✓
60 kW200 mm150 mm––✓

Maximum thickness is a ceiling, cut slowly and with a rougher edge. Plan daily production a few millimetres below it, and confirm with the cutting chart of the exact source and head in your quotation.

Typical Cutting Speeds

Carbon steel, oxygen (0.5–0.7 bar, positive focus)
Thickness6 kW12 kW
3 mm3.5–4.2–
4 mm3.3–3.8–
6 mm2.7–3.2–
8 mm2.2–2.5–
10 mm2.0–2.32.0–2.3
12 mm1.9–2.13.0–3.5
16 mm1.2–1.42.8–3.0
20 mm0.6–0.71.5–1.6
25 mm0.4–0.50.8–1.0
Stainless steel, nitrogen (10–20 bar, negative focus)
Thickness6 kW12 kW
1 mm40–5050–60
2 mm25–3040–45
3 mm15–1830–35
5 mm7–815–18
6 mm6–713–15
8 mm3.5–3.88–10
10 mm1.6–2.06.5–7.5
12 mm1.0–1.25.0–5.5
16 mm0.5–0.62.0–2.3
20 mm0.2–0.351.2–1.4

Speeds in m/min. Typical values for good-quality cutting; edge requirements, material grade, gas purity and the head change them. Your quotation includes the chart for the exact configuration.

High Power on a Compact Bed

Thick-plate parts such as flanges, brackets, base plates and machine parts are often small. Cutting them on a 3012 bed gives you the source power without paying for and housing a 4 m or 6 m machine. Three things scale with the power, not with the bed: the chiller, the electrical supply and the gas supply. Plan them for the source you choose, and plan a crane for heavy plate.

The 1200 mm width takes 1250 × 2500 mm plates directly. If you buy 1500 × 3000 mm plates, look at the LFP3015 or the 4020 machines.

Why Auto-Focus Matters on Thick Plate

Thick plate is pierced in stages, each with its own focus and height, and oxygen cutting moves the focus further up as the plate gets thicker. The auto-focus head takes these values from the cutting program, so the operator does not reset lenses for each job, and pierces and cuts come out the same every time.

Where It Sits in the PCL Laser Range

ModelWorking areaPowerBest for
GF3012 (this machine)3000 × 1200 mm6–60 kWHigh power on a compact bed
LFP30153000 × 1500 mm1–12 kWOpen single table; standard sheets
LFP40204000 × 2000 mm1–30 kWDual exchange table for volume
LFH40204000 × 2000 mm1–30 kWHigh-power plate on a plate-welded bed
LFP60206000 × 2000 mm1.5–3 kWLong sheets at lower investment
LFH60206000 × 2000 mm1–12 kWLarge-format production
2-in-1 sheet & tube3015 or 4020 + tubes Ø20–220 mm1–12 kWSheet and tube on one machine

Common Problems and How to Fix Them

ProblemUsual causeWhat to do
Pierce blow-out on thick plateSingle-step pierce on heavy plateUse staged piercing and let the plate cool between pierces
Heavy dross under thick carbon steelSpeed too high, oxygen pressure low, focus too negative, nozzle partly blockedReduce speed by 5–8 %; keep oxygen at 0.5–0.7 bar; set focus +3 to +4 mm; check the nozzle
Not cutting throughPierce not finished, focus not positive enough on oxygen cuts, dirty protective windowLet all pierce stages finish; raise focus in 1 mm steps; clean or replace the window
Dross under stainless or aluminiumSpeed too high, nitrogen pressure too low or focus not deep enoughLower the speed or raise pressure; move the focus down (negative) as thickness grows

What Decides the Price

ItemOptionsEffect
Laser sourceBrand (Raycus, IPG, Max) and powerThe largest single item; higher power costs more and needs a bigger chiller and supply
Cutting headRaytools or WSX auto-focusAuto-focus and protection against collisions
DriveServo brand, rails and racksAccuracy over the years
Power6–60 kWThe source is most of the price; higher power also needs a larger chiller, power supply and gas supply

The GF3012 is quoted on request.

From Inquiry to Production

  1. Parts and samples. Send your thickest parts and materials; we cut samples on the power you are considering.
  2. Configuration. We fix the source, head, table and options, and send a layout with floor space, power, gas and extraction connections.
  3. Build and test. The machine is assembled and tested before shipment; lead time is confirmed in the quotation.
  4. Site preparation. Level floor, power supply, assist gas and compressed air, and fume extraction ready before arrival.
  5. Installation and training. Quoted with the machine; operators learn nesting, cutting parameters, daily checks and simple fault finding.
  6. Support. 24-month warranty on the whole machine, consumables excluded.

Before You Order

  • Thickest plate and the thickness you cut most hours.
  • Crane for loading heavy plate.
  • Power supply, chiller and gas supply for the chosen source.
  • Plate sizes: the bed takes 1250 × 2500 mm directly.

Maintenance

WhenWhat
DailyCheck and clean the protective window; check nozzle condition and centring; check gas pressures.
WeeklyRemove slag; clean slats and rails; check the height sensor.
PeriodicallyReplace slats; lubricate rails and racks; change chiller water and extraction filters.

Safety

Laser light reflected from the sheet is invisible and can injure eyes, so the cutting area must be enclosed or fenced off and the door interlocks must stay working. Keep the extraction running and its filters clean; dust in the bed and filters can catch fire, especially after aluminium. Keep oxygen equipment free of oil and grease, and secure gas cylinders.

GF3012 FAQ

What is the working area of the GF3012?

3000 × 1200 mm.

Which power options are there?

Fiber sources from 6 kW up to 60 kW.

How thick can it cut?

Typical maximums are 25 mm carbon steel and 20 mm stainless at 6 kW, about 40 mm of both at 12 kW, and far more at 20–60 kW. Daily production runs a few millimetres below the maximum.

Which files can it read?

AI, BMP, PLT, DXF and DST among others.

Why put high power on a 3012 bed?

Thick-plate parts are often small. The compact bed gives you the source power without the cost and floor space of a 4 m or 6 m machine.

What does high power need on site?

A larger power connection, a chiller matched to the source and a gas supply for high consumption; the layout drawing lists them for your configuration.

Compare all fiber laser cutting machines side by side in our selection guide.

Send your thickest parts and material. We suggest the source power and quote the GF3012.

Get a quote

Laser Cutting Samples

Fiber laser cutting samples in mild steel and stainless steel
Sample parts in mild steel and stainless steel. The thickness you can cut depends on the laser source power; send your drawing for samples on your material.

Machine Structure: Gantry or Desk Type

Fiber laser cutters are built in two basic ways. The structure decides how well the machine keeps its accuracy at high acceleration and under the heat of long cutting runs.

Gantry structure with separate rails

Gantry structure (PCL standard)

  • Rails apart from the cutting table: heat from the cutting zone goes into the table, not into the frame that carries the rails.
  • Dual drive: both sides of the gantry are driven, so it stays square at high acceleration.
  • Open sides: sheets can be loaded by forklift or crane from the side.
  • Service: worn table slats and parts are replaced without touching the rails.
Integrated welded desk-type bed

Integrated desk structure

  • One welded body: table and rails sit on the same frame, which is compact and costs less.
  • Heat: cutting heat goes into the same frame that carries the rails, which matters more at high power and on long runs.
  • Loading: closed sides make loading large, heavy sheets slower.
  • Best for: lower power, smaller sheets and limited budgets.

At high power and high acceleration, the gantry structure keeps the precision parts away from the heat of cutting. That is why PCL builds its fiber laser cutters this way.

Machine Bed: Plate-Welded or Tube-Welded

The bed carries the gantry and takes every acceleration of the cutting head. How it is built decides how long the machine keeps its accuracy, especially above 3 kW and on heavy plate.

PCL plate-welded machine bed

Plate-welded bed (PCL standard)

  • Thick steel plate: welded from 12–16 mm carbon steel plate; the mass damps vibration at high acceleration.
  • Stress relief: annealed at about 600 °C and cooled slowly in the furnace, so welding stresses do not distort the bed later.
  • Machined in one set-up: all mounting faces for rails and racks are milled on a large gantry milling machine in a single clamping, so they stay parallel.
Tube-welded machine bed

Tube-welded bed (economy design)

  • Hollow square tube: lighter and cheaper, but more prone to vibration at high acceleration.
  • Thinner walls: more sensitive to heat and to the forces of heavy plate and fast moves.
  • Best for: low power and thin sheet, where loads are small.

When comparing quotations, ask how the bed is built, whether and how it is stress-relieved, and how the mounting faces are machined. These answers say more about long-term accuracy than the accuracy figure on the data sheet.

Global Delivery & Logistics

From our factory to your workshop: secure packing, careful handling and reliable international shipping, followed by installation support and warranty service.

Export packing of a CNC machine
1Export packingEach machine is cleaned, rust-protected, wrapped and fixed in export packaging built for the sea voyage.
CNC machine loaded and secured in a shipping container
2Container loadingMachines are loaded, braced and secured in the container, and checked against the packing list before sealing.
Container ship for international delivery
3Ocean shippingShipped from Qingdao or other Chinese ports on request. Prices are usually quoted FOB Qingdao; shipping documents travel with the cargo.
4Installation & support
  • Installation guidance and operator training
  • On-site installation available on request
  • 24-month warranty on the whole machine
  • Remote technical support by video and phone