LFP3015: Overview
The LFP3015 is our open single-table laser for 3000 × 1500 mm sheets. Most customers buy it as their first laser: it takes the sheets they already stock, needs no exchange table or enclosure, and can be ordered with anything from a 1 kW to a 12 kW source.
LFP3015 Cutting Demonstration
The LFP3015 cutting on its open table.
Technical Specifications
| Working area | 3000 × 1500 mm |
|---|---|
| Layout | Open frame, single table |
| Laser source | 1–12 kW; Raycus, IPG or Max |
| Positioning accuracy | ±0.03 mm |
| Max linkage speed | 100–120 m/min |
| Materials | Carbon steel, stainless steel, aluminium, brass |
| Price | USD 18,000–35,000 FOB Qingdao, depending on source and options |
| Certification | CE, ISO 9001 |
| Warranty | 24 months on the whole machine (consumables excluded) |
What the Power Options Cut
Typical maximum thickness from 1 kW to 60 kW; the last column marks the powers this machine can carry. Treat the figures as the ceiling, not the daily working range. Even 1.5 kW reaches about 16 mm carbon steel, so lower powers cover a lot of steel work; the bigger sources mainly add stainless and aluminium thickness and speed.
| Laser power | Carbon steel (O₂) | Stainless (N₂) | Aluminium (N₂) | Brass (N₂) | This model |
|---|---|---|---|---|---|
| 1 kW | 10 mm | 5 mm | 3 mm | 3 mm | ✓ |
| 1.5 kW | 16 mm | 6 mm | 4 mm | 3 mm | ✓ |
| 2 kW | 20 mm | 8 mm | 6 mm | 5 mm | ✓ |
| 3 kW | 22 mm | 10 mm | 8 mm | 6 mm | ✓ |
| 4 kW | 25 mm | 12 mm | 10 mm | 8 mm | ✓ |
| 6 kW | 25 mm | 20 mm | 16 mm | 12 mm | ✓ |
| 8 kW | 40 mm | 30 mm | 30 mm | 16 mm | ✓ |
| 12 kW | 40 mm | 40 mm | 40 mm | 16 mm | ✓ |
| 20 kW | 80 mm | 100 mm | 60 mm | 20 mm | – |
| 60 kW | 200 mm | 150 mm | – | – | – |
Maximum thickness is a ceiling, cut slowly and with a rougher edge. Plan daily production a few millimetres below it, and confirm with the cutting chart of the exact source and head in your quotation.
Typical Cutting Speeds
| Thickness | 1.5 kW | 3 kW | 6 kW | 12 kW |
|---|---|---|---|---|
| 2 mm | 5.0 | 3.8–4.2 | – | – |
| 3 mm | 3.6 | 3.2–3.6 | 3.5–4.2 | – |
| 4 mm | 2.5 | 3.0–3.2 | 3.3–3.8 | – |
| 6 mm | 1.4 | 2.2–2.5 | 2.7–3.2 | – |
| 8 mm | 1.2 | 1.8–2.2 | 2.2–2.5 | – |
| 10 mm | 1.0 | 1.0–1.3 | 2.0–2.3 | 2.0–2.3 |
| 12 mm | 0.8 | 0.9–1.0 | 1.9–2.1 | 3.0–3.5 |
| 16 mm | 0.5 | 0.6–0.7 | 1.2–1.4 | 2.8–3.0 |
| 20 mm | – | 0.5–0.55 | 0.6–0.7 | 1.5–1.6 |
| 25 mm | – | – | 0.4–0.5 | 0.8–1.0 |
| Thickness | 1.5 kW | 3 kW | 6 kW | 12 kW |
|---|---|---|---|---|
| 1 mm | 20 | 28–35 | 40–50 | 50–60 |
| 2 mm | 7 | 18–24 | 25–30 | 40–45 |
| 3 mm | 4.5 | 7–10 | 15–18 | 30–35 |
| 5 mm | 1.5 | 3.0–3.6 | 7–8 | 15–18 |
| 6 mm | 0.8 | 2.0–2.7 | 6–7 | 13–15 |
| 8 mm | – | 1.0–1.2 | 3.5–3.8 | 8–10 |
| 10 mm | – | 0.5–0.6 | 1.6–2.0 | 6.5–7.5 |
| 12 mm | – | – | 1.0–1.2 | 5.0–5.5 |
| 16 mm | – | – | 0.5–0.6 | 2.0–2.3 |
| 20 mm | – | – | 0.2–0.35 | 1.2–1.4 |
Speeds in m/min. Typical values for good-quality cutting; edge requirements, material grade, gas purity and the head change them. Your quotation includes the chart for the exact configuration.
Living with an Open Table
Everything is within reach: you can watch the head, pull a part halfway through a job, and put a sheet on with a forklift from the side. The price for that is idle time, because the laser waits while the sheet is cleared and reloaded. On one-off and short-run work that hardly matters. Once the machine runs the same parts all shift, the LFP4020 with an exchange table earns more.
An open machine also needs the area around it organized: a guarded zone so that nobody walks through the beam path, and fume extraction connected to the bed.
Where It Sits in the PCL Laser Range
| Model | Working area | Power | Best for |
|---|---|---|---|
| GF3012 | 3000 × 1200 mm | 6–60 kW | High power on a compact bed |
| LFP3015 (this machine) | 3000 × 1500 mm | 1–12 kW | Open single table; standard sheets |
| LFP4020 | 4000 × 2000 mm | 1–30 kW | Dual exchange table for volume |
| LFH4020 | 4000 × 2000 mm | 1–30 kW | High-power plate on a plate-welded bed |
| LFP6020 | 6000 × 2000 mm | 1.5–3 kW | Long sheets at lower investment |
| LFH6020 | 6000 × 2000 mm | 1–12 kW | Large-format production |
| 2-in-1 sheet & tube | 3015 or 4020 + tubes Ø20–220 mm | 1–12 kW | Sheet and tube on one machine |
Typical Work
- Steel and aluminium signage letters.
- HVAC duct parts and brackets.
- Electrical enclosures and panels.
- Furniture frames.
- Short-run parts for local customers.
Common Problems and How to Fix Them
| Problem | Usual cause | What to do |
|---|---|---|
| Dross under stainless or aluminium | Speed too high, nitrogen pressure too low or focus not deep enough | Lower the speed or raise pressure; move the focus down (negative) as thickness grows |
| Not cutting through | Pierce not finished, focus not positive enough on oxygen cuts, dirty protective window | Let all pierce stages finish; raise focus in 1 mm steps; clean or replace the window |
| Burnt corners and small holes | Heat builds up where the head slows down | Use corner power ramping; change cut order to spread the heat |
| Parts tip up and hit the head | Small parts falling between slats | Leave micro-joints; replace worn slats; cut small parts last |
| Yellow or brown stainless edge | Nitrogen below 99.99 % purity, low pressure, stand-off too high or a leak | Use at least 99.99 % nitrogen; set stand-off to about 0.5 mm; add 1–2 bar; leak-test fittings |
What Decides the Price
| Item | Options | Effect |
|---|---|---|
| Laser source | Brand (Raycus, IPG, Max) and power | The largest single item; higher power costs more and needs a bigger chiller and supply |
| Cutting head | Raytools or WSX auto-focus | Auto-focus and protection against collisions |
| Drive | Servo brand, rails and racks | Accuracy over the years |
| Table | Open single table | Lowest cost in the range; no exchange table |
The LFP3015 is USD 18,000–35,000 FOB Qingdao; the source brand and power make most of the difference.
From Inquiry to Production
- Parts and samples. Send a few typical drawings, materials and thicknesses; we cut samples on the power you are considering.
- Configuration. We fix the source, head, table and options, and send a layout with floor space, power, gas and extraction connections.
- Build and test. The machine is assembled and tested before shipment; lead time is confirmed in the quotation.
- Site preparation. Level floor, power supply, assist gas and compressed air, and fume extraction ready before arrival.
- Installation and training. Quoted with the machine; operators learn nesting, cutting parameters, daily checks and simple fault finding.
- Support. 24-month warranty on the whole machine, consumables excluded.
Before You Order
- Your sheet size, and whether you also buy 1250 × 2500 mm sheets.
- Thickness mix by hours per month.
- Gas: compressed air for thin sheet, nitrogen for stainless, oxygen for thick steel.
- Space around the bed for a guarded zone and forklift loading.
Maintenance
| When | What |
|---|---|
| Daily | Check and clean the protective window; check nozzle condition and centring; check gas pressures. |
| Weekly | Remove slag from the slats; clean dust from rails and racks; check chiller water level. |
| Periodically | Replace worn slats; lubricate rails and racks; change chiller water; change extraction filters. |
Safety
An open machine has no housing around the beam, and the light reflected from the sheet is invisible and can injure eyes. Keep the area around the bed fenced off while cutting, give anyone inside it laser safety glasses rated for the wavelength, and keep the extraction running. Slag and dust in the bed can catch fire, especially after cutting aluminium; clean the bed regularly and keep an extinguisher nearby. Oxygen cylinders and lines must be kept free of oil and grease.
Strengths and Limits
Strengths
- Takes standard 1500 × 3000 mm sheets
- Lowest investment in the range
- Open access for loading and inspection
Limits to know
- Laser waits during loading
- Needs a guarded area
- Not built for long unattended runs
LFP3015 FAQ
What sheet size does the LFP3015 take?
Sheets up to 3000 × 1500 mm, the standard 10 × 5 ft format.
How much does the LFP3015 cost?
USD 18,000–35,000 FOB Qingdao. The source brand and power make most of the difference.
Which power should I choose?
Choose by the thickness you cut most hours, not the thickest plate you might see once a year. Then check that thickness against the chart of the quoted source.
Is the LFP3015 enclosed?
No, it is open. For an exchange table and higher output, see the LFP4020.
What gas do I need for the LFP3015?
Compressed air covers thin carbon and stainless sheet cheaply; nitrogen gives bright stainless edges; oxygen is used for thicker carbon steel.
Can I upgrade the power later?
The source is a major component; plan the power you need at purchase. Ask us before ordering if you expect to move to thicker plate.
Compare all fiber laser cutting machines side by side in our selection guide.
Send your sheet sizes and thickness mix. We suggest a source and quote the LFP3015 with every component brand named.
Get a quote









