LFP4020: Overview
The LFP4020 is a production laser for 4000 × 2000 mm sheets with an automatic dual exchange table. While one sheet is cut, the next is loaded on the other table, and the two swap in 15–20 seconds. It takes sources from 1 kW to 30 kW.
LFP Series in Operation
Cutting on the LFP large-format series.
Technical Specifications
| Working area | 4000 × 2000 mm |
|---|---|
| Laser source | 1–30 kW; Raycus or IPG |
| Exchange table | Dual table, automatic, 15–20 s |
| Positioning accuracy | ±0.03 mm |
| Max acceleration | 1.2–1.5 G |
| Frame | Heavy-duty, stress-relieved |
| Certification | CE, ISO 9001 |
| Warranty | 24 months on the whole machine (consumables excluded) |
Where the Exchange Table Pays
Count how long the laser stands still per sheet today: clearing parts, removing the skeleton, craning in the next sheet. On a single table that time is lost on every sheet. With the exchange table it happens during cutting, and the loss shrinks to the 15–20 second swap. The more sheets per shift, the faster the table pays for itself.
What the Power Options Cut
Typical maximum thickness from 1 kW to 60 kW; the last column marks the powers this machine can carry. Treat the figures as the ceiling, not the daily working range. The speed tables stop at 12 kW; for 20–30 kW, ask for the chart of the exact source you are quoted. At high power the gains are mainly speed on medium and thick plate.
| Laser power | Carbon steel (O₂) | Stainless (N₂) | Aluminium (N₂) | Brass (N₂) | This model |
|---|---|---|---|---|---|
| 1 kW | 10 mm | 5 mm | 3 mm | 3 mm | ✓ |
| 1.5 kW | 16 mm | 6 mm | 4 mm | 3 mm | ✓ |
| 2 kW | 20 mm | 8 mm | 6 mm | 5 mm | ✓ |
| 3 kW | 22 mm | 10 mm | 8 mm | 6 mm | ✓ |
| 4 kW | 25 mm | 12 mm | 10 mm | 8 mm | ✓ |
| 6 kW | 25 mm | 20 mm | 16 mm | 12 mm | ✓ |
| 8 kW | 40 mm | 30 mm | 30 mm | 16 mm | ✓ |
| 12 kW | 40 mm | 40 mm | 40 mm | 16 mm | ✓ |
| 20 kW | 80 mm | 100 mm | 60 mm | 20 mm | ✓ |
| 60 kW | 200 mm | 150 mm | – | – | – |
Maximum thickness is a ceiling, cut slowly and with a rougher edge. Plan daily production a few millimetres below it, and confirm with the cutting chart of the exact source and head in your quotation.
Typical Cutting Speeds
| Thickness | 1.5 kW | 3 kW | 6 kW | 12 kW |
|---|---|---|---|---|
| 2 mm | 5.0 | 3.8–4.2 | – | – |
| 3 mm | 3.6 | 3.2–3.6 | 3.5–4.2 | – |
| 4 mm | 2.5 | 3.0–3.2 | 3.3–3.8 | – |
| 6 mm | 1.4 | 2.2–2.5 | 2.7–3.2 | – |
| 8 mm | 1.2 | 1.8–2.2 | 2.2–2.5 | – |
| 10 mm | 1.0 | 1.0–1.3 | 2.0–2.3 | 2.0–2.3 |
| 12 mm | 0.8 | 0.9–1.0 | 1.9–2.1 | 3.0–3.5 |
| 16 mm | 0.5 | 0.6–0.7 | 1.2–1.4 | 2.8–3.0 |
| 20 mm | – | 0.5–0.55 | 0.6–0.7 | 1.5–1.6 |
| 25 mm | – | – | 0.4–0.5 | 0.8–1.0 |
| Thickness | 1.5 kW | 3 kW | 6 kW | 12 kW |
|---|---|---|---|---|
| 1 mm | 20 | 28–35 | 40–50 | 50–60 |
| 2 mm | 7 | 18–24 | 25–30 | 40–45 |
| 3 mm | 4.5 | 7–10 | 15–18 | 30–35 |
| 5 mm | 1.5 | 3.0–3.6 | 7–8 | 15–18 |
| 6 mm | 0.8 | 2.0–2.7 | 6–7 | 13–15 |
| 8 mm | – | 1.0–1.2 | 3.5–3.8 | 8–10 |
| 10 mm | – | 0.5–0.6 | 1.6–2.0 | 6.5–7.5 |
| 12 mm | – | – | 1.0–1.2 | 5.0–5.5 |
| 16 mm | – | – | 0.5–0.6 | 2.0–2.3 |
| 20 mm | – | – | 0.2–0.35 | 1.2–1.4 |
Speeds in m/min. Typical values for good-quality cutting; edge requirements, material grade, gas purity and the head change them. Your quotation includes the chart for the exact configuration.
Choosing Between 1 kW and 30 kW
The frame is the same; the source decides cost and capability. On thin sheet the cycle is limited by the 1.2–1.5 G acceleration, not by power. Power earns its money on plate: a 3 kW source cuts 10 mm carbon steel at about 1.0–1.3 m/min with oxygen, 6 kW at 2.0–2.3 m/min, and higher power raises that speed and the thickness you can cut with a clean edge.
Where It Sits in the PCL Laser Range
| Model | Working area | Power | Best for |
|---|---|---|---|
| GF3012 | 3000 × 1200 mm | 6–60 kW | High power on a compact bed |
| LFP3015 | 3000 × 1500 mm | 1–12 kW | Open single table; standard sheets |
| LFP4020 (this machine) | 4000 × 2000 mm | 1–30 kW | Dual exchange table for volume |
| LFH4020 | 4000 × 2000 mm | 1–30 kW | High-power plate on a plate-welded bed |
| LFP6020 | 6000 × 2000 mm | 1.5–3 kW | Long sheets at lower investment |
| LFH6020 | 6000 × 2000 mm | 1–12 kW | Large-format production |
| 2-in-1 sheet & tube | 3015 or 4020 + tubes Ø20–220 mm | 1–12 kW | Sheet and tube on one machine |
Plan the Site
- A power connection for the source, chiller and extraction together.
- Gas supply sized for your nitrogen use.
- Floor space for both tables and sheet handling.
- Fume extraction and a guarded work area.
Common Problems and How to Fix Them
| Problem | Usual cause | What to do |
|---|---|---|
| Table exchange stops | Slag on the exchange rails or chain | Clean the exchange rails and check the limit switches |
| Pierce blow-out on thick plate | Single-step pierce on heavy plate | Use staged piercing and let the plate cool between pierces |
| Heavy dross under thick carbon steel | Speed too high, oxygen pressure low, focus too negative, nozzle partly blocked | Reduce speed by 5–8 %; keep oxygen at 0.5–0.7 bar; set focus +3 to +4 mm; check the nozzle |
| Dross under stainless or aluminium | Speed too high, nitrogen pressure too low or focus not deep enough | Lower the speed or raise pressure; move the focus down (negative) as thickness grows |
| Dimensions drift over a long sheet | Dirt on racks or rails, or thermal growth of the plate | Clean rails and racks; cut in an order that spreads the heat |
What Decides the Price
| Item | Options | Effect |
|---|---|---|
| Laser source | Brand (Raycus, IPG, Max) and power | The largest single item; higher power costs more and needs a bigger chiller and supply |
| Cutting head | Raytools or WSX auto-focus | Auto-focus and protection against collisions |
| Drive | Servo brand, rails and racks | Accuracy over the years |
| Exchange table | Automatic dual table | Standard on the LFP4020; raises laser-on time |
| Automation | Loading and unloading systems | For long unattended runs |
The LFP4020 is quoted on request.
From Inquiry to Production
- Parts and samples. Send your production volume, sheet sizes and thickness mix; we size the source and estimate output.
- Configuration. We fix the source, head, table and options, and send a layout with floor space, power, gas and extraction connections.
- Build and test. The machine is assembled and tested before shipment; lead time is confirmed in the quotation.
- Site preparation. Level floor, power supply, assist gas and compressed air, and fume extraction ready before arrival.
- Installation and training. Quoted with the machine; operators learn nesting, cutting parameters, daily checks and simple fault finding.
- Support. 24-month warranty on the whole machine, consumables excluded.
Before You Order
- Sheets per shift and average cutting time per sheet.
- Thickness mix, to size the source between 1 and 30 kW.
- Crane or forklift for loading the exchange table.
- Power supply and nitrogen supply for high-power cutting.
Maintenance
| When | What |
|---|---|
| Daily | Check and clean the protective window; check nozzle condition and centring; check gas pressures. Check the exchange table travel. |
| Weekly | Clean slag from both tables and the exchange rails; clean rails and racks. |
| Periodically | Replace slats; lubricate rails, racks and exchange drive; change chiller water and filters. |
Safety
Laser light reflected from the sheet is invisible and can injure eyes, so the cutting area must be enclosed or fenced off and the door interlocks must stay working. Keep the extraction running and its filters clean; dust in the bed and filters can catch fire, especially after aluminium. Keep oxygen equipment free of oil and grease, and secure gas cylinders.
Strengths and Limits
Strengths
- Loading during cutting
- 1–30 kW on one frame
- High acceleration
Limits to know
- Needs more floor space than a single table
- High power needs a large supply and gas
- Exchange mechanism to maintain
LFP4020 FAQ
How fast does the LFP4020 change tables?
The automatic exchange table swaps in 15–20 seconds.
What power can it take?
1 kW to 30 kW fiber sources from Raycus or IPG.
Is high power worth it on thin sheet?
Rarely. On thin sheet acceleration sets the pace; high power pays off on medium and thick plate.
Can I see cuts on my material?
Yes. Send a drawing, material and thickness.
How much floor space does the exchange table need?
More than a single-table 4020, because the second table sits beside the bed. The layout drawing in the quotation shows the exact space.
Can it be automated further?
Yes. Ask about loading and unloading systems for your sheet sizes.
Compare all fiber laser cutting machines side by side in our selection guide.
Send your volume and thickness mix. We size the source and quote the LFP4020 with site requirements.
Get a quote










